Topcoat over MIL-PRF-23377J primer or MIL-DTL-53022 primer
A two-component epoxy polyamide topcoat for spray and brush application with a maximum VOC of 4.7 lbs./gallon (563 grams/liter).
1. Color:
Fed. Std 595 Colors 1XXXX
Fed. Std 595 Colors 2XXXX
Fed. Std. 595 Colors 3XXXX
2. Volume Solids:
25.9 – 31.6% (For Gloss colors)
29.4 – 33.9% (For Semigloss colors)
27.3 – 35.2% (For Flat colors)
3. Solids by Weight:
32.6 – 40% (For Gloss colors)
36.1 – 44.6% (For Semigloss colors)
37.9 – 46% (For Flat colors)
4. Viscosity: 40 KU minimum 1 hours after mixing
5. DFT: 1.0 – 1.2 mils
6. Theoretical Coverage @ 1 mil dft: 415 – 565 ft2/gallon (varies by color and gloss)
7. Gloss @ 60º
Fed. Std 595 Colors 1XXXX (80 minimum)
Fed. Std 595 Colors 2XXXX (15 – 30)
Fed. Std. 595 Colors 3XXXX (8 maximum)
8. Dry Time
Set to Touch: 1 hour max..
Dry Hard: 7 hours max.
Complete Cure: 7 days
9. Pot Life: 8 hours maximum
10. Mix Ratio
1:1 by volume
1 part Component A
1 part Component B
11. VOC: 3.5 – 4.7 lbs/gallon (415 – 565 grams/liter) (varies by color and gloss)
12. Induction Time: 1 hour
Order as little as 4 gallons! Call Chance at 800 563-1305 x 101 or email Chance to buy or request a FREE quote.
APPLICATION
Steel: Surface must be clean and free of grease, dirt, oil, rust and other contaminants that could interfere with proper adhesion.
Aluminum: Surface must be clean and free of grease, dirt, oil, rust and other contaminants that could interfere with proper adhesion.
Galvanized and other metals: Clean and remove surface contamination including oxidation. .
Reduction: Reduce with MIL-T-81772 Type 2 as required.
Conventional Spray:
Atomizing Pressure: 45 – 55 psi
Pot Fluid Pressure: 10 – 20 lbs.
Airless Spray:
Tip Size: 0.011 – 0.015” orifice
Atomizing Pressure: 1800 – 2200 psi
Clean-up:
Clean tools and equipment immediately after use with MEK, MAK or MIL-T-81772 Type 2 thinner.
Safety Precautions:
This product is intended for professional use in an industrial environment only. Consult the Material Safety Data Sheet prior to application.
Products are warranted to meet its internal specifications and are of merchantable quality. However, the purchaser is solely responsible for the suitability of the product for any particular application. The purchaser should thoroughly test or qualify the product for serviceability, environmental compliance and health and safety factors prior to use. Further, our total liability is limited to the price of the product or replacement in kind.
Call Chance at 800 563-1305 or email Chance to buy or request a FREE quote.
Do you have rust on your various metals? Then you do not have the Metal Guard 700!
/in Ecolink News/by Industrial DegreasersPreventing Rust on Blackened, Phosphated, and Bare Metal has Never Been Simpler
Rust usually is the sign of the end of the line of metal that has proved durable for numerous years, but why not prevent rust accumulation and prolong the life and functionality of your metals? Metal Guard 700 is an emulsion rust preventative that offers outstanding corrosion protection to blackened, phosphated, and bare metal surfaces during storage and transportation. This rust prevention product has a list of impressive properties and attributes, a few of which are listed below.
Has the idea of preventing rust buildup sparked your interest in the Metal Guard 700? Call or email Jackie for more information at 1-800-886-8240 or jhooper@ecolink.com.
No Longer a Vicious Cycle
Your problems should not have solutions that create additional problems. Using hazardous nitrite or primary amine-based chemistries to improve your corrosion issues might solve short-term problems, but it is not a desirable long-term solution. The answer is Metal Guard 700! This rust preventative is a non-mineral oil, and a nitrite and primary amine-free corrosion.
Who can use the Metal Guard 700? This rust elimination product benefits all industries working with nickel-plated parts and other various metals.
Metal Guard 700 is better, safer, and faster than what is currently available from other manufacturers. How is this rust stopping solution better? After replacing traditional sodium nitrite rust inhibitors, it can reduce dumping from every two days to every five days. How is this rust eliminator safer? It contains no nitrites and amines, and has no mineral oil. How is this metal guarding solution faster? Its coating will air dry in a relatively short time.
To prove that our metal protecting solution is better than the rest, check out some of the competing products in the table below and see for yourself!
Still not convinced this emulsion rust preventative could solve your rust prevention needs? Call or email Jackie to find out how you can receive a FREE sample of Metal Guard 700 today! See the results for yourself! We have told why this metal guarding solution is better, safer, and faster—now let us show you why!
For more information, check out these great sources for another perspective!
Wikipedia | YouTube
Ecolink Collaborates to Promote Hazardous Source Reduction Globally
/in Ecolink News/by Industrial DegreasersHazardous Waste Minimization
October 2011 marked the 20th anniversary of Ecolink’s sustainable operations. The company was founded in response to the Montreal Protocol and the ban of Class 1 Ozone Depleting Solvents and other toxic industrial chemicals. As we embark on our next 20 years of serving the need for less, safer and compliant chemicals, we enlisted the help of other like-minded organizations and individuals.
Tuesday, February 14, 2012 – Valentine’s Day officially kicked off the beginning of our next chapter. We have worked closely with American Marketing Association (AMA-Atlanta) in support of GA DECA a high school marketing program with more than 10,000 students participating. Last Friday, we successfully recruited three AMA collegiate members for new product launch internships that run through April 22nd – Earth Day.
I am pleased to introduce our 3 very talented interns – Chance Hood, Courtney Rivkind and Jackie Hooper. Each intern will promote two brand new distributed products through our alliance partners: Randolph Products, Nugentec and Hubbard Hall respectively. We will emphasize social media as the primary way of accelerating exposure and engagement of these new strategic relationships and their unique products mutually selected. Each intern has 8 digital profiles and 2 merchandise promotions to design, implement and integrate. The intern who accumulates a combined score of most page views, on-page social sharing and return-on-investment (leads generated, quotes, samples, sales) will earn an extra $1,000 + donate $100 to their favorite charity.
Chance Hood is a 2nd year MBA student at Mercer University (Atlanta) expecting to graduate in May 2012. A 26 years old originally from Alabama, Chance graduated with a BBA in Marketing from The University of Montevallo in 2008. Chance has worked in restaurant/hospitality industry and as a licensed outside sales insurance agent before enrolling in Enterprise Rent a Car’s management trainee program where he worked for the largest stand-alone branch in region. While in his MBA program at Mercer University, Chance has maintained a 4.0 GPA and completed a sales strategy internship with Silverpop. Chance is tasked with promoting Ecolink’s entree into the world of mil-spec paints and coatings and working closely with the business development team at Randolph Products. How can Randolph Products reduce hazardous waste? By specializing as the largest produce of the smallest batches of paints, coatings and primers an by offering super low (4 gallon) minimum quantities for legacy mil-spec paints & coatings that typically require 20 gallon minimum order with a high % of unopened paint getting buried in landfills. (I’ve witnessed more than my share during 13 years of auditing facilities).
Please visit Chance’s two product pages and Like, Tweet, Digg, Google +, etc. [especially if you are family, friend, Mercer alumni, professor, fellow student] and help Chance make the most of his internship at Ecolink and also earn an extra $1,000 + $100 for charity:
https://ecolink.com/info/mil-dtl-11195g-type-2/
https://ecolink.com/info/mil-c-22750d/
====================================================================================================
====================================================================================================
Jackie Hooper
is a senior marketing major at Georgia College & State University where she serves as the VP of membership for her collegiate American Marketing Association chapter. Enthusiastic about the environment and sustainability as well as marketing and social media, Jackie feels extremely privileged to be able to combine the two into a valuable experience! Jackie will represent Hubbard Hall, the oldest privately help chemical company in the US with more than 5,000 commodity chemicals and an additional 1,000 specialty aqueous solutions, corrosion inhibitors, conversion coating and wastewater treatment. Jackie will work closely with Hubbard Hall’s distributor program manager to increase market share in select geographic markets within US. How can Hubbard Hall reduce hazardous waste? With more than 160 years of knowledge of chemistry, manufacturing ‘and’ regulatory compliance, Hubbard Hall maintains an extensive knowledge base of solved chemical-related problems. They also have tremendous technical bench strength for new product development.
Please visit Jackie’s two product pages and Like, Tweet, Digg, Google +, etc. [especially if you are family, friend, Georgia College & State University alumni, professor, fellow student] and help Jackie make the most of her internship at Ecolink and also earn an extra $1,000 + $100 for charity:
https://ecolink.com/info/low-voc-corrosion-protection-replaces-cosmoline-nitrites/
https://ecolink.com/info/hap-free-heavy-duty-industrial-paint-stripper/
MIL-DTL-11195G FAST DRY LUSTERLESS ENAMEL, TYPE 2
/in Ecolink News/by Industrial DegreasersQualified under MIL-DTL-11195G Type 2
A single component, HAPS free, corro
sion inhibiting coating for use on ammunition.
1. Color:
Fed Std. 35109
Fed Std. 36231
2. Volume Solids: 55.5 +/- 1%
3. Solids by Weight: 75.3 +./- 1%
4. Viscosity: 70 KU max. (reduced)
5. DFT: 1.0 – 1.5 mils
6. Theoretical Coverage @ 1 mil dft: 890 ft2/gallon
7. Gloss @ 60º: 2 – 8
8. Dry Time
Set to Touch: 6 minutes max.
Dry Hard: 12 minutes max..
9. VOC: 3.5 lbs/gallon (420 grams/liter)
Buy as little as 4 gallons! Call Chance at 800 563-1305 x 101 or email Chance to buy or request a FREE quote.
APPLICATION
Steel: Surface must be clean and free of grease, dirt, oil, rust and other contaminants that could interfere with proper adhesion. Pretreatment with TT-P-490E Type 1 or DOD-P-15328D Wash Primers will give the best adhesion and performance. When blasting the surface a minimum of SSPC-SP6 is required for best performance.
Aluminum: Clean with an appropriate cleaner to remove contamination from the substrate. Pretreat the surface with a wash primer or other conversion coating.
Galvanized and other metals: Clean and remove surface contamination including oxidation. Treat with a wash primer to improve adhesion to the substrate.
Note: Due to wide variations in substrates, surface preparation etc. It is recommended that the customer check adhesion and compatibility.
Reduction: Reduce 8 parts of enamel with 1 part of thinner A-A-3007 by volume.
Conventional Spray:
Atomizing Pressure: 45 – 55 psi
Pot Fluid Pressure: 10 – 15 lbs.
Airless Spray:
Tip Size: 0.015 – 0.021” orifice
Atomizing Pressure: 2200 psi minimum
Clean-up:
Clean tools and equipment immediately after use A-A-3007 thinner.
Safety Precautions:
This product is intended for professional use in an industrial environment only. Consult the Material Safety Data Sheet prior to application.
Products are warranted to meet its internal specifications and are of merchantable quality. However, the purchaser is solely responsible for the suitability of the product for any particular application. The purchaser should thoroughly test or qualify the product for serviceability, environmental compliance and health and safety factors prior to use. Further, our total liability is limited to the price of the product or replacement in kind.
Call Chance at 800 563-1305 or email Chance to buy or request a FREE quote.
MIL-C-22750D EPOXY POLYAMIDE COATING – TYPE 1
/in Ecolink News/by Industrial DegreasersTopcoat over MIL-PRF-23377J primer or MIL-DTL-53022 primer
A two-component epoxy polyamide topcoat for spray and brush application with a maximum VOC of 4.7 lbs./gallon (563 grams/liter).
1. Color:
Fed. Std 595 Colors 1XXXX
Fed. Std 595 Colors 2XXXX
Fed. Std. 595 Colors 3XXXX
2. Volume Solids:
25.9 – 31.6% (For Gloss colors)
29.4 – 33.9% (For Semigloss colors)
27.3 – 35.2% (For Flat colors)
3. Solids by Weight:
32.6 – 40% (For Gloss colors)
36.1 – 44.6% (For Semigloss colors)
37.9 – 46% (For Flat colors)
4. Viscosity: 40 KU minimum 1 hours after mixing
5. DFT: 1.0 – 1.2 mils
6. Theoretical Coverage @ 1 mil dft: 415 – 565 ft2/gallon (varies by color and gloss)
7. Gloss @ 60º
Fed. Std 595 Colors 1XXXX (80 minimum)
Fed. Std 595 Colors 2XXXX (15 – 30)
Fed. Std. 595 Colors 3XXXX (8 maximum)
8. Dry Time
Set to Touch: 1 hour max..
Dry Hard: 7 hours max.
Complete Cure: 7 days
9. Pot Life: 8 hours maximum
10. Mix Ratio
1:1 by volume
1 part Component A
1 part Component B
11. VOC: 3.5 – 4.7 lbs/gallon (415 – 565 grams/liter) (varies by color and gloss)
12. Induction Time: 1 hour
Order as little as 4 gallons! Call Chance at 800 563-1305 x 101 or email Chance to buy or request a FREE quote.
APPLICATION
Steel: Surface must be clean and free of grease, dirt, oil, rust and other contaminants that could interfere with proper adhesion.
Aluminum: Surface must be clean and free of grease, dirt, oil, rust and other contaminants that could interfere with proper adhesion.
Galvanized and other metals: Clean and remove surface contamination including oxidation. .
Reduction: Reduce with MIL-T-81772 Type 2 as required.
Conventional Spray:
Atomizing Pressure: 45 – 55 psi
Pot Fluid Pressure: 10 – 20 lbs.
Airless Spray:
Tip Size: 0.011 – 0.015” orifice
Atomizing Pressure: 1800 – 2200 psi
Clean-up:
Clean tools and equipment immediately after use with MEK, MAK or MIL-T-81772 Type 2 thinner.
Safety Precautions:
This product is intended for professional use in an industrial environment only. Consult the Material Safety Data Sheet prior to application.
Products are warranted to meet its internal specifications and are of merchantable quality. However, the purchaser is solely responsible for the suitability of the product for any particular application. The purchaser should thoroughly test or qualify the product for serviceability, environmental compliance and health and safety factors prior to use. Further, our total liability is limited to the price of the product or replacement in kind.
Call Chance at 800 563-1305 or email Chance to buy or request a FREE quote.
Fluorinated Heat Transfer Fluids Sale
/in Ecolink News/by Industrial DegreasersSpecial savings available for Solvay Galden and 3M™ Fluorinert™ users
Fluorinated heat transfer fluids are among the most expensive in the chemical industry. Commonly associated with single phase heat transfer applications in the semiconductor manufacturing industry these materials are well-suited to a variety of semiconductor manufacturing heat transfer applications, such as etchers, ion implanters and testers.
Other safe heat transfer media for demanding applications including:
Applications consist of component immersion, wafer etching, ion implantation, radar equipment, transformers, power supplies, UF6production, chillers, cooling towers, and freeze dryers.
CF3 – (OCFCF2)n – (OCF2)m – OCF3
CF3
3M™ Fluorinert™ and Solvay Galden are the two market leaders. With few suppliers, consumers must be resourceful in how they buy, use and dispose of these valuable materials. The great news is that these materials can be reclaimed to their original state at fraction of the cost of new. Reusing inert heat transfer fluids many times gains greater cost efficiencies. Under most conditions you can expect 90% of the contaminated fluid returned to like new quality resulting in minimal hazardous waste disposal. Using reclaimed heat transfer fluids decreases downtime on equipment & significantly improves your MRO budgett.
To learn more about ways to save money through extending the life of your fluorinated heat transfer fluids, please call Courtney at 800 563-1305 or email Courtney to buy or request a FREE quote.
HT-200 is a high performance, inert fluid suitable for use in HEAT TRANSFER and DIELECTRIC APPLICATIONS requiring:
• High Thermal Stability
• Good Dielectric Properties
• Excellent Chemical Inertness
• Good Compatibility with metals, plastics and elastomers
• No Flash or Fire Point, No AutoIgnition Point
• Safety